series voltage ( c : 16v ) capacitance lot no. capacitance lot no. a2 150c cw plastic platform 0.3max. l 0.3 d 0.5 b 0.2 c 0.2 0.5max. a 0.2 a 0.2 e h positive negative series voltage ( v : 35v ) trade mark plastic platform 0.3max. l 0.5 d 0.5 b 0.2 c 0.2 0.5max. a 0.2 a 0.2 e h positive negative a2 220v cw pressure relief vent u 1 c 2 w 3 1 4 a 5 1 6 5 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (150 f) rated voltage (10v) series name type d 5 6.3 8 10 code cl nl (mm) a b c e l h 5 7 2.1 5.3 5.3 1.3 7.0 0.5 to 0.8 6.3 7 2.4 6.6 6.6 2.2 7.0 0.5 to 0.8 6.3 8.7 2.4 6.6 6.6 2.2 8.7 0.5 to 0.8 8 10 2.9 8.3 8.3 3.1 10 0.8 to 1.1 10 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 d l chip type type numbering system (example : 10v 150 f) aluminum electrolytic capacitors cw series chip type, low impedance, long life assurance chip type with load life of 7000 hours at +105 c . low impedance temperature range up to +105 c . applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2002/95/ec). specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 25 to +105 c 6.3 to 50v 10 to 470f 20% at 120hz, 20 c after 2 minutes' application of rated voltage, leakage current is not more than 0.01 cv or 3 (a) , whichever is greater. black print on the case top. the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 7000 hours at 105 c. after storing the capacitors under no load at 105 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. cw cb measurement frequency : 120hz at 20 c measurement frequency : 120hz z 25 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 10 3 6.3 4 16 2 25 2 35 2 50 2 rated voltage (v) tan (max.) 50 0.14 35 0.14 25 0.16 16 0.26 10 0.28 6.3 0.32 within 30% of the initial capacitance value less than or equal to the initial specified value 300% or less than the initial specified value capacitance change tan leakage current capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. dimension table in next page. ( 5 to 6.3 ) ( 8 to 10 ) voltage v 6.3 10 16 25 35 50 code j acevh low impedance cat.8100b
frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.35 0.50 0.64 0.83 1.00 cw series aluminum electrolytic capacitors taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. 10 22 33 47 100 150 220 330 470 100 220 330 470 101 151 221 331 471 5 7 6.3 7 6.3 8.7 6.3 8.7 8 10 2.2 1.1 1.0 1.0 0.22 95 140 230 230 600 1h 50 0j 6.3 1a 10 1c 16 1e 25 1v 35 5 7 6.3 7 2.2 1.1 95 140 5 7 6.3 7 6.3 7 6.3 8.7 6.3 8.7 8 10 8 10 2.2 1.1 1.1 1.0 1.0 0.22 0.22 95 140 140 230 230 600 600 5 7 6.3 7 6.3 7 6.3 8.7 8 10 8 10 10 10 2.2 1.1 1.1 1.0 0.22 0.22 0.16 95 140 140 230 600 600 850 5 7 5 7 6.3 8.7 6.3 8.7 8 10 10 10 2.2 2.2 1.0 1.0 0.22 0.16 95 95 230 230 600 850 8 10 8 10 10 10 0.53 0.53 0.35 350 350 670 v code cap. (f) impedance case size d l (mm) rated ripple dimensions max. impedance ( ? ) at 20 c 100khz, rated ripple current (marms) at 105 c 100khz cat.8100b
|
